Thermal Stress Analysis: Equations and FEA Example
Introduction
Thermal stress analysis explains why a heated component can remain nearly motionless yet develop substantial internal forces. You will learn how to derive the governing equation, solve a restrained-bar example, and check a thermal-structural simulation. These skills connect undergraduate mechanics with the design of piping, heat exchangers, and precision assemblies.
Thermal Stress Analysis and the Thermal Expansion Coefficient
A homogeneous bar heated uniformly expands freely if its supports permit movement. For small strains and a constant thermal expansion coefficient, its free extension is ΔL = αLΔT, where α is expansion per unit temperature, L is original length, and ΔT is the temperature change. Thermal strain is therefore ε_th = αΔT.
Expansion alone does not create stress in this ideal case. Stress develops when supports, adjacent materials, or incompatible expansion within a temperature gradient restrict the preferred deformation. The United States Department of Energy materials handbook describes this distinction and explains how rapid heating or cooling can create damaging gradients.
Thermal Stress Analysis: Derivation and Worked Example
For a slender, linearly elastic bar carrying uniaxial stress, total axial strain combines elastic and thermal contributions: ε_total = σ/E + αΔT. Here E is Young’s modulus and tensile stress is positive. If rigid supports prevent all axial extension, ε_total = 0, giving the thermal stress formula σ = −EαΔT.
The minus sign means uniform heating creates compression under these assumptions; cooling produces tension. This result assumes constant properties, no initial stress, uniform temperature, and freedom to deform laterally. It is not a general formula for three-dimensional constraint or plastic deformation.
Consider a 1 m steel bar with area A = 100 mm², using illustrative values E = 200 GPa and α = 12 × 10^-6 K^-1. Heating it from 20°C to 80°C gives ΔT = 60 K. Its free extension would be ΔL = 12 × 10^-6 × 1 × 60 = 0.00072 m, or 0.72 mm.
With complete axial restraint, σ = −200,000 × 12 × 10^-6 × 60 = −144 MPa. The corresponding axial force is N = σA = −14,400 N, so each end transmits a 14.4 kN compressive-force magnitude. Compare this elastic prediction with the material’s temperature-dependent yield strength before accepting the model.
ANSYS Thermal-Structural Analysis Workflow
In ANSYS thermal-structural analysis, first solve a steady-state or transient thermal model using credible conductivity, heat input, and convection conditions. Then transfer the temperature field into a structural model and specify the stress-free reference temperature. Supply elastic modulus, Poisson’s ratio, and expansion data with consistent units and appropriate temperature dependence.
For the benchmark above, represent axial restraint without unnecessarily locking lateral expansion, while removing rigid-body motion. Check axial stress away from support effects, displacement, and reaction forces against the analytical values. Refine the finite element analysis mesh and monitor meaningful quantities rather than trusting a single peak stress.
This workflow matters for heat-exchanger tubes, exhaust systems, and motor housings, where temperature changes interact with mounts and joints. An Ansys update published on 17 November 2026 highlights combined structural-thermal evaluation, including thermal expansion, in Creo Ansys Simulation Advanced. The software development reinforces the practical value of understanding the mechanics before interpreting simulation results.
Common Mistakes with Boundary Conditions
Do not apply σ = EαΔT to every heated part: a freely expanding homogeneous bar under uniform heating has zero thermal stress in the ideal model. Check whether actual supports slide, flex, or contain clearances. Also distinguish a temperature rise from an absolute temperature; Celsius and kelvin increments match, but their absolute values do not.
Do not assume uniform average temperature captures thermal shock or that a sharp-corner peak will converge. Nonuniform temperatures can produce self-equilibrating stresses, while idealized restraints can create numerical singularities. Investigate support realism, temperature gradients, and material nonlinearity before judging safety from a contour plot.
Conclusion
Thermal stress analysis starts with thermal strain and the constraints that convert expansion into force. Use the restrained-bar calculation as a verification benchmark, then add realistic supports, temperature fields, and material behavior for practical designs. Explore more mechanical engineering topics on Mechtics, or share a thermal-loading question in the comments.


